How To Cut Down A Tree With A Chainsaw Near A House

How Much Does It Cost To Cut Down a Tree Near a House?

Tree removal services for cutting a tree down near house can cost anywhere from $150 to $2,000. A good average will be from $700 to $800, with tree removal costs varying based on the size of the tree, with larger trees costing more than a small tree close to a house.

If you decide to cut down a tree yourself, there is much more to understand and much safety equipment required to avoid serious injury, regardless of how large or small your tree is.

cut down tree

Tree Cutting Tools and Equipment

  • Chainsaw
  • Chainsaw Bar & Chain Oil
  • Felling Wedges
  • Hard Hat
  • Protective eyewear
  • Hearing Protection
  • Work Gloves
  • Chaps
  • Steel-Toe Boots
  • Chainsaw Protective Gear Kit
  • Ladder
  • Rope

Preparation

  • Ensure you know how to use your new chainsaw and have the proper chainsaw bar for the job.
  • It’s not easy to know how to cut down a large tree near a house as branches and limbs can easily fall.
  • To stay safe, follow these steps:
  • Before using any power tools, make sure they are in safe working order.
  • Use new cutting blades and chains.
  • Wear gloves, boots, and a hard hat to protect your hands, feet, and head.
  • To avoid slipping when using an extension ladder, tie it to the tree using a rope.
  • Make a request for help to cut down large trees. Directing falling branches and trunk portions offer more control when you have a helper.
  • Check there are no power lines in the vicinity. Even smaller branches can fall and cause a power outage.
  • When removing larger trees, these safety steps are required to protect yourself and everyone else in the felling zone.

How Do You Make a Tree Fall Where You Want It To?

You can use these instructions for felling a large tree that is 20 feet tall or more.

They will keep you and your home safe while also allowing for fast tree removal. The steps here will keep your home safe, and make sure you get the tree to fall where you want it to fall. (Learn How To Cut Palm Tree)

Clear the Area

Move vehicles, lawn ornaments, equipment, or other obstacles out of the way before you start cutting. This will protect them from being damaged by tree limbs or falling branches.

To make your job easier, prune back shrubs or plants around the tree-felling zone if possible.

Make that all pets and small children are kept safely inside. This will eliminate the possibility of them injuring themselves when a tree falls.

cutting branch of a tree

Remove Upper Branches

  1. To secure your extension ladder to the tree, you’re cutting, set up your tripod ladder, and use a rope.
  2. Chop off the higher branches with your reciprocating saw, but rather than climbing the ladder with the saw in your hand, tie a rope to the saw’s handle and carry it up with you.
  3. Safer still, bring the saw up to yourself once you’ve reached the top of the ladder and secured yourself in the upper portion of the tree.
  4. Tie a rope around heavy branches that may fall and cause harm to your home when cutting them down.
  5. Small branches can be cut without a rope if they are away from your home, and they will fall in the right direction.
  6. Then, on the ground, tie the other end around another tree trunk. Once cut, you can untie the rope around the tree trunk and slowly lower the branch to the ground with your helper.

When lowering a limb, make sure not to wrap the rope around your hand or fingers. The weight of a branch can draw a rope tight around your fingers, causing significant harm.

Cut Off Lower Branches

It’s time to work closer to the ground now that you’ve trimmed off the higher branches. Because the branches on the lower portions of the tree are usually broader and heavier, a chainsaw is an appropriate tool for the job.

  1. Make an undercut by sawing upwards from the underside of the branch, about 1/4 of the way through the branch.
  2. Saw downwards from the branch’s top, 6–12 inches further from the trunk than the undercut, after the initial cut. The branch will fall smoothly without splintering or breaking if you make two incisions this way.
  3. Branches that have been poorly cut are more likely to splinter and fall in unpredictable ways or even swing back at you and your ladder.
  4. A branch that has been correctly chopped will fall straight down.
  5. To avoid damage to your home, use the rope method from step 2 to control the fall of branches as needed.

Note: In these steps, you use methods where the terming could be confusing.

When you cut downward, the chain pulls the saw away from you; this is known as cutting with a pulling chain. Alternatively, you can use the top of the bar to cut upward, called cutting with a pushing chain. (Learn How To Kill A Tree Without Cutting It Down)

Fell the Trunk

You’ll have the trunk standing in your yard, which should be fully de-limbed. To fell a tree follow these steps:

  1. Make the first cut a right-angle notch cut in the tree trunk with your chainsaw in the direction you want it to fall.
  2. The notch should be deep enough to go 1/4–1/3 of the way through the tree’s diameter.
  3. The saw sideways for the second cut turn and cut horizontally to meet your first cut, creating a notch and making sure the two cuts meet.
  4. Make sure there are no people or obstructions in the way of the falling tree.
  5. Move to the opposite side so you can make your horizontal cut above the previous cut, which make up your felling cut.
  6. To keep the saw from binding, saw until you have enough room to slide a wedge into the incision. In this cut, insert the tree-felling wedge, pointing in the direction you wish the tree to fall.
  7. Drive the wedge in and finish the cut, making sure the blade does not come into contact with the felling wedge.
  8. Don’t sever the tree’s trunk, so it acts as a hinge; once the tree starts to fall into the fall zone, stop cutting and start moving along your escape path.
  9. Your helper can gently pull on a guide rope to help the tree follow its intended line of falling, so it will tip as you want it to.

Note, if your tree leans in one direction, that is the way it will want to fall. Felling such trees is best left to the pros who do tree felling for a living.

Cut Stump at Ground Level

After the tree has been felled, cut the stump at or near ground level with your chainsaw.

  1. Trying to get rid of a stump and its root system can be tough. If the stump isn’t causing any problems where it is, treat it with a stump killer and let it decompose naturally.
  2. Cut the stump flush with the ground using your chainsaw.
  3. To prevent the tree from resprouting, apply stump killer to the stump.
  4. Stump killer will prevent the felled tree from sprouting from the stump, saving you time and work in the future.

Cut the Tree Into Sections

  1. Now that your tree is on the ground chop the trunk and limbs into chunks using your chainsaw. Sections of forearm length are easy to dispose of and use as firewood.
  2. Cut the tree trunk and limbs into forearm-length parts using the chainsaw.
  3. These portions can either be discarded or divided for use as firewood.
  4. If you don’t need firewood, post a free firewood ad. While you may not require firewood from the tree, your neighbors may.

fallen tree

How-to fell a Tree Summary

In summary, you can use these steps to ensure the safe and efficient removal of small trees or other trees you are confident you can remove without injury or damage.

By using ropes to secure large branches before cutting, you can lower large branches, control where they will end up on the ground, and prevent falling branches from damaging your home. (Find the Best Tree And Shrub Fertilizer)

Tree removal near houses necessitates adopting appropriate safety precautions and following certain procedures to ensure a safe and efficient removal. To get rid of a tree that is over 20 feet tall near your home, follow these steps:

  1. Clear the area of vehicles and items that falling branches or trunk sections may damage.
  2. Use a reciprocating saw to remove upper branches.
  3. Use a chainsaw and employ the 2 felling cut method to remove large lower branches safely.
  4. Notch your tree in the direction you want it to fall. Then, make your felling cut on the opposite side, toward the notch, to fell the tree.
  5. Cut the stump flush with the ground and treat it with a stump killer.
  6. Saw your felled trunk and limbs into forearm-length sections for firewood or disposal.

How To Cut Down A Tree With A Chainsaw Near A House (2)

Leave a Comment

Your email address will not be published. Required fields are marked *