How To Cut Vinyl Lattice

Vinyl is increasingly gaining popularity as a substitute for making a fence, rails, or even replacing a wooden lattice or wood fencing. Plastic lattice is an excellent landscaping item since it won’t rot, is insect-resistant, and is simple to maintain. However, handling and cutting it might be difficult.

Vinyl is almost maintenance-free, and when it requires attention, it’s usually only a quick wash to remove dirt and dust, which you can do easily with a power washer.

Vinyl lattice may be cut to size in the same ways that wood lattice can; however, certain saw blades and the sort of saw you can use are better for the work than others. To make things far more straightforward, we have a guide on how to cut lattice the right way.

vinyl lattice

By the end, you’ll have all you need to find the right tools to make a task that you can accomplish quickly, with only a little bit of effort. (Read Can You Stain Particle Board)

What Do I Use To Cut vinyl lattice?

Vinyl fence and PVC lattice can be cut in the same ways as wood: a table saw, or a circular saw.

Whether you’re building a fence yourself or working on another vinyl fence job, you’ll almost certainly need to trim your material to match your needs.

To prevent chipping and give your vinyl project the most outstanding possible appearance, make sure your cuts are straight and smooth.

Steps On How To Cut Lattice

Measure the distance your fence material needs to cover with a tape measure.

With a pencil, mark this distance on your vinyl. Next, draw a line down the length of your vinyl with a T-Square guide and note where you need to cut.

To begin, cut your vinyl lattice. Then, use a circular saw and a vinyl-cutting blade to cut through the lattice, joint by joint.

You can now cut your vinyl fence components. Use a circular saw with your vinyl-cutting blade to now cut your vinyl fence.

Saw between, not through, fence panels or pickets. This will result in clean cuts and a professional finish.

Re-notch your fence rails by sliding vinyl fence notchers into the end of your cut rail.

You can rip fence posts with your trim saw to finish the job. When cutting posts, start at the bottom and cut your way up. Doing this means you can hide any cuts in the soil.

Remove the post’s cap if you need to cut a post already in the ground. Measure your length and cut straight with your fine-toothed saw. Cut the post evenly, and then replace the cap.

Note: If you don’t have a vinyl-cutting blade, use a fine-toothed blade. Carefully guide the saw blade through the lattice.

To avoid chipping, wear eye protection and possibly a mask to stop breathing dust while cutting vinyl. (Read Best Way To Cut Vinyl Siding)

Is It Easy To Cut Vinyl Lattice?

Here you can see the proper ways you should cut lattice panels. Circular saws work like table saws yet are portable and cut wood on site.

Even with a fine-toothed blade to prevent chipping, you need to take caution when using circular saws in the garden.

Before you saw, put on safety equipment. To safeguard your eyes, wear plastic safety glasses. Work gloves should be used while handling and cutting the lattice, just in case any splinters or chips fly.

  1. Draw a straight cut line on the lattice with a straightedge and a pencil.
  2. Mark the lines where it has to be cut once you’ve got your measurements. Carefully draw a light line down the back of the lattice where it has to be trimmed with a carpenter’s pencil.
  3. Remove any staples or nails along the pencil line using a flat screwdriver. Manufacturers commonly use Staples and nails to help the lattice keep its shape, although they can be dangerous when sawing.
  4. This will make the cutting procedure easier and reduce the chances of staples flying up and harming you.
  5. To cut the lattice, lay it face down on a flat surface. A strong plank or a worktable will suffice. Next, place the lattice on the surface with the front, or imitation wood grain side, facing down.
  6. To keep the lattice stable and help you cut in a straight line, place many clamps at either end of the lattice away from the cut line.
  7. Release the blade lever on the back of a circular saw to adjust the blade depth.
  8. Hold the saw against the lattice as if you were about to cut it, then lower the blade to about 0.5 inches below the lattice’s level. To secure, push the blade lever back into place.
  9. Plastic lattice is typically 0.5 in thick, but you can double-check the thickness with a ruler.
  10. Use a vinyl-cutting blade for plastic or solid core vinyl lattice.
  11. A reciprocating saw or a Sawzall with fine teeth can also be used, but anything with a high-speed saw blade suited for wood should be avoided. The extra length of the teeth is too large, causing the plastic to chip.
  12. Squeeze the saw’s trigger and cut along the line slowly and steadily.
  13. Position the saw exactly along the pencil line, then begin cutting the lattice with care and precision.
  14. Follow the pencil line as closely as possible at a slow pace. Once you’ve reached the end, turn off the saw and cut it cleanly through. Your lattice is now ready for installation.

cutting tool

What Is The Best Tool To Cut Lattice?

Lattice is constructed up of strips that are linked in a diagonal crisscross pattern, and most lattice sheet will be made of wood or plastic.

The perforations between the strips let air move through the lattice, providing a slight breeze and a viewable wall or structure.

Lattice is commonly used to cover regions under pier and beam houses and the undersides of decks.

You will find many blades work differently than others, and being sharp is merely one factor in the choice of blade.

One of the best and quickest ways is to measure and cut lattice using a circular saw with fine teeth on the blade. The edge won’t splinter, and you can get fine cuts for when you need to frame an area.

handsaw

Can you cut vinyl lattice with a hand saw?

The finest saw blade for cutting vinyl lattice has small, straight teeth, not hooked or rip-and-tear teeth like saw blades made to cut tough lumber.

Vinyl lattice can be cut with any sharp, medium, or fine-toothed saw blade. A carbine blade is also suitable. (Learn How To Cut Drywall)

You can use a circular saw, handsaw, or trim saw. When cutting vinyl or polyvinyl chloride, several tool companies sell circular saw blades explicitly developed for cutting vinyl or polyvinyl chloride. Otherwise, a handsaw should suffice.

More crucial than the blade is a saw you can handle. Unless you know someone who has used a circular saw and will teach you how to operate it securely, a handsaw may be better.

Tips for Cutting Lattice

Vinyl lattice can be bonded or have staples or nails; however, they are more prevalent in wood than vinyl lattice.

Remove any staples or nails from the area to be cut before cutting vinyl lattice panels.

Holding lattice steady when cutting might be difficult because of its wide weave. So use clamps or a friend to hold the lattice tightly when you cut it.

Less hold means less chance of vinyl chipping or splitting along the cut line. Never cut vinyl lattice in temperatures below 32°F.

Important Safety Concerns

When cutting vinyl lattice, always use safety precautions. Small fragments may fly into your eyes when it cracks or chips, causing injury and difficulty seeing.

When handling and cutting vinyl lattice, use protective gear such as gloves and goggles, and keep the saw blade sharp. A dull blade will not cut vinyl neatly and smoothly.

How To Cut Vinyl Lattice (2)

Leave a Comment

Your email address will not be published.