What To Put On Outside Steps To Prevent Slipping

If you’ve been wondering what to put on exterior steps to keep them from slipping, then you can find out here. When it is misting, raining, or winter, your exterior stairs become extremely dangerous with slippery steps outside.

Because they make most steps of wood or concrete, which are usually very smooth, water makes them exceedingly slippery and challenging to prevent slips when least unexpected.

Slippery outside steps are a safety danger, as it is hard to see where there are risks.

Ramp strips for outside steps

In our guide, you can learn more about how to fix this issue using outdoor non-slip stair treads for snow or other methods to keep your steps safe.

In the end, you can keep your family safe by knowing how to use non-slip strips for outside steps or using other non-slip surfaces. (Learn How To Soften Grout For Removal)

How to Make Your Steps Slip Resistant

Here are some of the best to deal with slippery surfaces on your outdoor steps.

Anti-Slip Strips

Anti Slip Strips offer non-slip safety for Kids, the elderly, and the rest of the family. The advantage of these being transparent is they don’t stop you from seeing your finished wood steps because of the anti-slip strips.

Some products offer a roller for installation, while some are made from self-adhesive strips that you peel and stick onto your stair tread.

The strips can work for both indoor and outdoor steps and also on other surfaces besides wood. The easy-to-apply self-adhesive strips can be hard to change and can attract dirt with lots of use.

Here are the steps to install non-slip strips for outdoor stairs.

  1. Using hot water, combine a few drops of home alkaline-based cleaning. Scrub the steps’ surface with a scrub brush.
  2. Rinse the steps with clean water and make sure your steps are thoroughly dry.
  3. Drop some water on the steps to make sure they’re clean. If the water beads, repeat the cleaning instructions. All remaining dirt and pollutants are washed away from the stairs if the water spreads out and wets the surface.
  4. Remove one strip’s sticky backing. Place the strip flat and near 1/2 to 1 inch of a step’s front edge. It should be pressed into position and won’t move once installed.
    Apply pressure across the entire strip with a roller or similar device to secure it in place.
  5. While the stages are ready to use right away, the adhesive may take up to 24 hours to fully activate and cure.
  6. Add a strip to each step as needed. Add two strips at every step if you desire.

Elogio Carpet Stair Treads Set of 13 Non SlipSkid Rubber Runner Mats or Rug Tread – Indoor Outdoor Pet Dog Stair Treads Pads – Non-Slip Stairway Carpet Rugs (Gray) 8 x 30

Stair Carpet Treads

Stair treads are a non-slip carpet material used for stair treads. You can find these with a rubber backing of a set size and come without glue or adhesive strips, thus causing no damage to hardwood stair treads.

The stair carpet strips come in a variety of designs, so picking one suitable outdoors is possible. They are easy to install as you sit them on the steps, and the sticky but not adhesive–backing holds them in position.

The strips tend to be used indoors, and you may need to search for ones suitable for outdoors to prevent serious injuries. (Learn How To Get Wrinkles Out Of Carpet)

Anti-Slip Tape

Anti-slip tape offers traction grit you can apply to outdoor stair treads. The anti-slip tape will stick and provide a non-slip surface for stairs. In the most basic form, it is 80 grit sandpaper coupled with an adhesive backing.

The main issue with using anti-slip tape on wood stairs in your home is difficult to remove. Because the adhesive backing is harsh on wood finishes, expect the wood steps finish to come off with the tape when you remove them.

Metal Treads

You’ll find these used in walkways and steps as they are highly durable and offer a texture that won’t wear when installed.

Here are the steps to install the metal tread plates on wood steps or concrete to prevent slips.

  1. To eliminate any debris, clean the steps with water. Allow enough time for the steps to dry.
  2. Attach a metal anti-slip covering to the front edge of the step, centered side to side, within 1 inch.
  3. Drill four pilot holes in the step below and through the openings on the lid.
  4. If the steps are made of concrete or another masonry product, use masonry anchors. Four No. 8 stainless steel screws secure the anti-slip coating.
  5. Continue to cover each step with the remaining coverings.

Anti-slip spray for wood stairs

Anti-Slip Spray

Anti-slip spray for wood outdoor stairs is a cheaper alternative than a roll-on non-slip coating or other anti-slip finishes.

It is also the most straightforward anti-slip product to apply and is completely transparent. Finally, this product is affordable and can be used on concrete stairs or wood stairs.

However, the anti-slip spray may not last or deliver the look you want compared to other treatments to prevent slipping on a stair tread. It can change the wood color and collect dirt; thus, durability is a concern, and changing it is almost impossible.

If your wooden steps have been finished, it’s impractical to expect a spray-on surface coating to make no difference. Even if the product claims to be “transparent,” multiple coatings of such sprays are typically required, and it can make your stairs look different, especially when you add the coating to prevent slipping on your stairs annually.

Add Grit to Paint to Prevent Slips

Wood steps can be made slip-resistant by adding various types of grit to paint. Even as the paint starts to wear away, you won’t notice it if you use special plastic slip-resistant grit.

Before winter approaches, apply a coat of paint and traction grit to slick wood steps and seal them.

Apply a fresh layer of paint to the stairwell. Cover the area with a thick layer of rubber grit right away. Allow for drying time. Apply a second coat to seal the grit.

Although sand and aluminum oxide grit is both inexpensive, they both necessitate regular churning. They become dark flecks as soon as the paint fades away. However, you can paint the surface before sanding it; the second layer preserves the surface and prevents deterioration once winter arrives.

Instead, go to your local home improvement store and look for polymeric plastic grit. When you add polymeric grit, it stays suspended in the paint. Since, it’s made of transparent plastic, it won’t show up as dark specks once the paint wears away. (Read Will Vinegar Remove Paint From Concrete)

Add rubber grit to the paint if you want a grit that’s easier on bare feet and won’t slip. It’s long-lasting, won’t stain, and provides plenty of traction to prevent a fall from a previously slippery surface.

The other advantage with this is, you can do the same thing on concrete using durable floor paint, and here you get the same level of traction when you walk on it. It is cheap to apply, and you can use sand rather than purchasing a specialized traction surface.

Fixing these slippery issues annually is straightforward, as all it takes is another coat of paint and a sprinkling of natural sand to increase traction with your DIY non-slip paint.

What To Put On Outside Steps To Prevent Slipping

Leave a Comment

Your email address will not be published. Required fields are marked *